Sangoma VoiceTimeのインストール方法

    目次
    ヘッダーがありません

    2024年 5月 2日, 17:21 現在の版

    この版へ

    版の一覧 に戻る。

    現在の版を閲覧

     thumb_voice_time.gifUT50thumb_voice_time_int.gifUT51


    Sangoma社はAsteriskのタイミングソースデバイスとして、UT50とUT51を発売しました。UT50は外部USBポートに接続するため、UT51はサーバー内部のUSBポートに接続するためのものです。お使いのサーバーに内部増設用のUSBポートがある場合は、UT51を選択すると誤ってデバイスが抜ける危険がありません。

    Fonality社はこのデバイスを正式認定デバイスとしてサポートを開始しました。

    以下は、trixboxProで本デバイスを利用するためのインストール方法です。

     

    注意!!:この作業では、root権限をサーバーに設定します。trixboxProがリモートアクセスのために外部のインターネットにマウントされている場合は、侵入される危険がありますので、アクセス制限やRSA認証などの手段でサーバーを保護してから作業を行ってください。

     

    コンソールから以下のコマンドを実行してください。

    [root@trixboxNNNNNN ~]# yum clean all   [root@trixboxNNNNNN ~]# yum update FONdetect   [root@trixboxNNNNNN ~]# yum install wanpipe_voicetime-modules-2.6.9-42.EL wanpipe_voicetime-modules-2.6.9-42.ELsmp

    それから以下のコマンドを実行します

    [root@trixboxNNNNNN ~]# exit

    trixboxProのターミナル画面に戻ります。

    以下のIDとPWでターミナル管理画面に入ります。

    ID:ip

    PW:ip

     

    以下の画面が表示されます。

    Network Config/Troubleshooter
    
     
    
     1. Set IP Address of this system
    
     2. Show IP Address of this system
    
     3. Run the PING utility
    
     4. Run the TRACEROUTE utility
    
     5. Display the DNS Nameserver configuration
    
     6. Display the route table
    
     7. Display the ARP table
    
     8. Show Analog Phone Line voltage levels
    
     9. Show T1 Status
    
    10. Show Active Calls
    
    11. Set 'root' password
    
    12. Reboot system
    
    13. Re-scan for PSTN cards
    
    14. Scan for new phones
    
     
    
    Q. Quit and exit this tool
     
    Selection: 13
    13番を選択し、USBデバイスをtrixboxProに認識させます。
     
    This option will erase and recreate all PSTN card configurations.
    
    Are you sure you want to re-detect PSTN cards? [y/n]: y
    
    WANPIPE USB Dummy Timer Interface
    
    Starting PBXtra Core service:                              [  OK  ]
    
    Starting FONmon service:                                   [  OK  ]

     

    これで作業完了です。

    インストールが正しく行われたかを確認するために、root権限で再びコンソール画面に入ります。

    以下のコマンドを実行してください。

    [root@trixboxNNNNNN ~]# zttest

    タイミングの正確さを示す指標が表示されます。表示される数値の平均が99.98%以上であれば、正しく動作しています。

    Opened pseudo zap interface, measuring accuracy...
    99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 100.000000% 99.987793%
    99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.975586% 99.963379% 99.987793%
    99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793%
    99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793%
    99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793%
    99.987793% 99.987793% 99.987793%
    --- Results after 42 passes ---
    Best: 100.000000 -- Worst: 99.963379 -- Average: 99.987212
     

    もし、正常に認識されていないようなら、サーバーを一度再起動してみます。

     

    Powered by MindTouch Core